Tornado ACS 33 (GB 115 V~) Version for Great Britain
The Tornado ACS 33 is designed for Great Britain with 115~V. The maximum power of 3,300 W is described as 33. In order to be able to use this power, the socket used must be protected with a 30 A fuse. If the fuse rating is lower, only 2 motors can be used. If a genset is used, it should be designed for a single-phase output power of 4,000 W.
The vacuum blasting machine Tornado ACS 33 is based on a worldwide patented negative pressure jet method, which as a mobile cleaning device is designed not bigger tham a common industrial vacuum cleaner.
The vacuum blasting machine includes a vacuum generator with the corresponding filter cartridge and dust deposition as well as the appropriate containers for the blast media. The additional components of the vacuum blasting machine include the jet cap and the jet lance.
Technical Data Tornado ACS 33 (GB)
| voltage: | 115 V~ / 50-60 Hz |
| power consumption: | max. 3.300 W |
| air flow rate: | 3 x 60 l/sec. |
| cable length: | 7 m |
| tare weight: | 41 kg |
| height: | 1.280 mm |
| length overall: | 630 mm |
| width incl. trolley: | 610 mm |
| length of hose package | 4,5 m |
| filling volume: | 8l max. |
| granulate flow rate: | 20 - 80 l/h |
| granulate consumption: | 0,2 - 0,4 l/h |
| setup time: | 5 min. |
| dismantling time: | approx. 5 min (cleaning incl.) |
| noise level: | max. 75 dB |
Face capacity of vacuum blasting machine Tornado ACS 33
The face capacity of the vacuum blasting machine Tornado ACS 33 strongly depends on the material to be removed and the hardness of the base coat. Therefore the face capacity amounts to 1,5 – 5,0 qm/h depending on the application. On very light applications, the face capacity is even above.
Functioning of vacuum blasting machine Tornado ACS 33
The vacuum blasting machine Tornado ACS 33 is easy to set up. All components are simply plugged together. After turning on the vacuum generator the abrasive is sucked from the container into the cleaning device. Subsequently the middle flap must be opened and closed again, to allow the cleaning machine Tornado ACS to be ready for use.
The jet cap is places on the work surface and adheres to it by the vacuum. In the jet cap a vacuum of about 150 mbar is generated. With the introductionof the jet lance into the jet cap the cycle is closed. The blasting material is sucked through the jet lance and is accelerated to about 400 km/h. With this speed the blasting media impinges on the surface to be worked on, which will be according to the needs cleaned, stripped or roughened.
This process can be optimally controlled by the user via three vision panels. After impinging, the granules and the removed debris are sucked in immediately. Inside the cleaning machine a fine dust filter is seperating the debris from the granules. The blasting media then gets back to the storage container for further processing. Due to the closed cycle, the cleaning device has a minimum granule consumption.
The vacuum blasting machine Tornado ACS 33 works with a low noise level (75 db) not louder than a common industrial vacuum cleaner. The unique minimally abrasive Vacuum jet method is protected by patent.
Applications of vacuum blasting machine Tornado ACS 33
The vacuum blasting machine Tornado ACS 33 is primarily used for the following applications:
- graffiti removal
- facade cleaning
- floor cleaning
- tile and grout cleaning
- tile cleaning
- saltpetre removal
- limestone removal
- lacquer removal from a boat
- fire damage restoration
- layer and lacquer removal
- listed surface cleaning
- special cleaning
- photo engraving on granite
Advantages of vacuum blasting machine Tornado ACS 33
The vacuum blasting machine Tornado ACS 33 has many advantages compared to the conventional sandblasting or a high pressure cleaner. The most important are:
- simple handling (no specialized staff necessary)- fast setup and dismounting (max. 5 minutes)- transport possible in any vehicle- only 115 V~/ 30 A power connection necessary- low noise level, da it works without compressor- protective clothing is not necessary- no use of water and chemicals (very eco-friendly)- environmentally friendly due to the closed cycle- working in public business (barriers not necessary)- blasting media can be reused up to 80 times (low cost for consumables)- no hazardous waste in the disposal- in winter with frost useable.
To demonstrate our surface-friendly working method, we will show you how to remove nail polish from fingernails without damaging the finger. A highlight at every trade fair.
